渔具超市
当前位置:首页 > 钓具DIY探索 > 竹子还可以这么做鱼竿 竹子制作路亚竿方法

竹子还可以这么做鱼竿 竹子制作路亚竿方法

免费渔具试用 钓鱼啦 www.diaoyula.com 来源:Illustrates how to make a bamb 作者:钓鱼啦 点击:
把这篇文章分享到: 分享到更多的地方


本图片是钓鱼啦在国外的一个网站找到的,文字不是很能理解其文字,所以钓鱼啦将其原文转载过来了,希望这些图对大家DIY钓具有所帮助。 Pictured above are most of the tools that are used for making split cane fly fishing rods. Included in this photo



买渔具上哪好?当然是易渔具商城啦!
渔具超市淘宝网性价比最高渔具推荐

本图片是钓鱼啦在国外的一个网站找到的,文字不是很能理解其文字,所以钓鱼啦将其原文转载过来了,希望这些图对大家DIY钓具有所帮助。

diaoyula.com

tonkin01a.jpg (63843 bytes)

Pictured above are most of the tools that are used for making split cane fly fishing rods.  Included in this photo are block planes, a scraper plane, splicing blocks, dial calipers, a dial indicator depth gauge, and three different types of planing forms for preliminary, secondary, and final planing.

钓鱼啦版权所有

tonkin01aa.jpg (40498 bytes) 内容来自diaoyula.com

 

copyright diaoyula

  更多钓鱼知识请访问钓鱼啦

 

tonkin02aa.jpg (52441 bytes)
  本文转载自钓鱼啦

This image shows the splitting process.  A standard screwdriver with a sharpened blade is driven into a cane strip, and then the gloved hand forces the strip into the sharpened edge of the screwdriver blade, thus splitting the strip down its length into two narrower pieces.  With experience one learns to steer the split so that it does not veer off course.

tonkin01cc.jpg (25363 bytes)

Some freshly split strips of Tonkin cane. The protrusions are the remains of nodal diaphragms, which occur both inside and outside the bamboo stalk at each node location. They will be mostly removed using a plane and a hand file, and then heat and pressure will be applied to flatten any remaining bumps. Some bamboo fly rod makers use a bench grinder or belt sander to remove much of this node material prior to flattening them with heat, to help expedite the process.

本文转载自钓鱼啦



tonkin02.jpg (55667 bytes)

Heating the node area with a heat gun to soften the cane.  After it is sufficiently heated the strip is firmly clamped in a vise to flatten the node area as it cools. In the past bamboo fly rod makers used alcohol burning lamps to heat the cane.

tonkin03.jpg (34725 bytes)

A strip of cane being planed in the preliminary planing form. The approximately 82° angle of the groove in this wooden form helps to start the first 60° angle on the bamboo strip as it is planed. After this 60° angle is created, the strip will be placed into a second wooden planing form that has a 60° groove in it.

tonkin04.jpg (43038 bytes)
 

  钓鱼知识学习网站

A strip in the 60° groove of the secondary planing form. Planing in this form will make the strips become equilateral triangles in section.

tonkin05.jpg (18284 bytes)
  钓鱼知识学习网站

Checking the accuracy of the 60° angles using a center gauge (image on left).  After completing the  secondary stage of rough planing the ends of the strips have the equilateral triangle shape that enables them to nest together to form a fly rod that is hexagonal. They will next be bound together with string and placed in a heat treating oven that will dry, straighten, and temper them. Note that the side of each strip that faces out still has the original enamel layer that serves as the protective natural coating on the exterior of the bamboo stalk. The side of the strips that have this coating is never planed, since the bamboo plant's most elastic fibers lie just underneath this thin enamel layer. The enamel will, however, be sanded off with fine grit sandpaper in the last stages of the fly rod's creation.

tonkin07.jpg (44902 bytes) 更多钓鱼知识请访问钓鱼啦

The six untapered triangular strips bound together with string (top image), forming the familiar hexagonal cross section that is typical of bamboo fly fishing rods. The string binding will enable the strips to heat cure in a straightened position, thus removing most of the kinks that each strip may have originally had. Most importantly, heating the strips in the 6' long oven (lower image) drives out excess moisture, and stiffens the cane somewhat. Many rodmakers believe that placing the rod section in an iron pipe that is then heated with a blow torch serves this function as well as a more expensive oven does.

tonkin08.jpg (32435 bytes)

After heat treating, the bamboo strips will be tapered on a set of adjustable planing forms made from two steel bars (adjustable wooden forms can also be used for final planing). The beveled edges of the bars create a 60° groove down the center of the form that is adjusted in depth by tightening or loosening bolts that draw together or push apart the two sides of the form. The depth of the groove at each point along the length of the planing form is what determines how much the strips will taper from the large butt end of the fly rod to the smaller tip end. This adjustment is done on the planing forms using the pictured dial indicator depth gauge. There are an infinite number of possible fly rod tapers that could be used, and to a great extent being a good split cane fly rod maker involves understanding how different taper designs effect the casting performance of any given fly rod.

w w w .d i a o y u l a . c o m


tonkin09.jpg (34310 bytes)

The taper being planed into one of the bamboo strips using the steel planing forms and a block plane. The side of the form shown is for planing the larger diameter butt section of the fly rod. The other side of the form has a shallower groove and is used for planing the fly rod's tip section.

tonkin10.jpg (39022 bytes)

钓鱼啦钓鱼网

The strips sometimes tend to tear at the irregularly grained node areas during planing. To smooth these areas out a scraper plane is used. Scraper planes are also often used to remove the last few thousandths of an inch of material to make the strips flush with the top surface of the steel planing form. Inexpensive hand held scraping blades will also work well for rod making.  A very thin spline for a tip section is being shown in the forms in this image.


相关关键字文章:钓鱼啦,自制鱼竿,路亚竿制作

顶一下
(41)
80.4%
踩一下
(10)
19.6%
------分隔线----------------------------
最新评论 查看所有评论
发表评论 我也要评论 点击进入评论页面
请自觉遵守互联网相关的政策法规,严禁发布色情、暴力、反动的言论。
评价:
表情:
用户名: 密码: 验证码:
赞助商链接
    渔具商城 钓鱼学校
推荐内容